Icynene Insulation Removal & Replacement Nationwide

Icynene Insulation Removal & Replacement in Cedar Park: What to Know First

We provide independent Icynene insulation removal and replacement in Cedar Park, typically completing most jobs in one to two days with a written price locked before any work starts. Most Icynene attic removals in a Cedar Park home this size run between $2,800 and $5,400 depending on square footage, contamination level, and whether the existing open-cell foam needs mechanical removal or can be scraped and vacuumed. Call (737) 245-6428 for a free written estimate with no obligation to book.

Call (737) 245-6428

This page is for homeowners in Cedar Park, Buttercup Creek, Ranch at Deer Creek, and surrounding neighborhoods who have Icynene spray foam in their attic or walls and need it removed due to failure, contamination, or remodeling. Wes Okafor and our crew have handled Icynene retrofits across Cedar Park since we opened under The Haven Standard, and we publish blower-door numbers on every applicable job so you can verify the result.

How Icynene Products Fail - and How We Fix Them

• Icynene Classic Max (open-cell, 0.5 lb/ft³) - moisture retention in Cedar Park’s humid shoulder seasons. Classic Max was widely installed in Central Texas homes built 2012-2018 for its lower per-board-foot cost, but its 4.0+ perms water vapor permeance becomes a liability when attic HVAC ducts sweat during March and October humidity spikes. We’ve pulled saturated Classic Max from Cedar Park attics where the foam held water against roof decking until the OSB delaminated. Our fix: mechanical removal with specialized foam planers, then blower-door-guided air sealing of top plates and can lights before installing a replacement product matched to the assembly’s drying potential.
• Icynene MD-R-200 (medium-density, 2.0 lb/ft³) - shrinkage at stud bay perimeters. MD-R-200 was marketed for wall cavities in energy-code-compliant builds, but we’ve found 3-8 mm gaps at the foam-to-stud interface in multiple Cedar Park homes where seasonal expansion and contraction stressed the adhesive bond. These gaps become convection loops that defeat the R-value you paid for. Our fix: selective removal using thermal imaging to locate the voids, then dense-pack replacement with a cellulose or mineral wool assembly that doesn’t rely on adhesive contact for its performance.
• Icynene LD-C-50 (low-density, 0.4 lb/ft³) - rodent nesting and biological contamination. The soft, friable texture that made LD-C-50 easy to trim also makes it ideal nesting material for roof rats, which are endemic to Cedar Park’s mature neighborhoods with live oak canopy. We removed 1,200 square feet of LD-C-50 from a home near Cypress Creek Road last spring where the attic smelled like a pet store until we stripped it to the deck. Our fix: full removal with HEPA vacuum containment, enzymatic treatment of substrates, and installation of a rigid-foam or mineral wool replacement that rodents won’t tunnel into.
• Icynene closed-cell products (1.7-2.0 lb/ft³ range) - thermal drift from improper mix ratios during original install. Closed-cell Icynene relies on precise A-side/B-side proportioning; when the rig was running hot or the hoses were too long on the original job, the resulting foam can read 10-20% below labeled R-value within five years. We identify this with core sampling and infrared thermography before removal. Our fix: documented core testing, full removal if drift exceeds 15%, and replacement with a product whose chemistry we verify with the manufacturer’s current data sheet - no guessing.
• Icynene in unvented roof assemblies - code non-compliance with 2021 IECC and local amendments. Cedar Park adopted Williamson County amendments that require vapor-permeable insulation or dedicated vent channels in certain unvented cathedral ceiling configurations. Pre-2021 Icynene installations often don’t meet this, and we’ve been called to remove foam so the assembly can be reconfigured with proper venting. Our fix: surgical removal preserving structural elements, then redesign with a vented assembly or approved vapor retarding strategy, documented with photos and a written scope for permit closeout.

Our Icynene Insulation Removal & Replacement Process

1. 1
   Pre-work blower-door test and written price. We pressurize the house to measure ACH50 - the air changes per hour at 50 Pascals pressure - and give you a flat written price before anyone enters the attic. Under Haven Standard Clause 1, no work starts without it.
2. 2
   Containment and negative-air setup. We seal the attic hatch, install poly isolation barriers, and run HEPA-negative air machines to prevent foam particulate from migrating into living spaces. This step is non-negotiable on every Icynene removal.
3. 3
   Mechanical removal and substrate assessment. Open-cell Icynene comes out with specialized planers and vacuum systems; closed-cell requires more aggressive mechanical stripping. We photograph every deck and joist bay for the Documented Photo Record you receive at job close.
4. 4
   Air sealing of the now-exposed envelope. With the foam gone, we can finally see the top plates, wire penetrations, and chimney chases. We seal these with fire-rated caulk, rigid foam, and weatherstripped boxes - the leaks that should have been fixed before the original insulation went in.
5. 5
   Replacement installation and post-work blower-door test. We install your chosen replacement material, then run a second blower-door test. You get both numbers in writing: the before and after. Seal the leaks first. Then insulate. The order matters more than the product.
6. 6
   Cleanup, photo record delivery, and 365-Day Done Right Promise activation. The crew vacuums to bare floors, you receive your photo documentation and warranty paperwork, and the Done Right Promise goes into effect - if it’s not right, we make it right.

What Icynene Insulation Removal & Replacement Costs in Cedar Park

These are real ranges for jobs we’ve completed in Cedar Park and nearby Williamson County neighborhoods. Your written estimate will land within these brackets or we’ll explain exactly why your situation differs.

Factors that increase cost: multiple HVAC penetrations through the foam, active rodent infestations requiring remediation before replacement, and homes built before 1990 with knob-and-tube wiring that must be addressed. Factors that don’t: we don’t charge extra for the blower-door tests, the photo documentation, or the written warranty - those are Haven Standard baseline. Call (737) 245-6428 for your free written estimate.

Why Cedar Park Homeowners Call Topside Attic Insulation Cedar Park for Icynene Work

We’re an independent Icynene service provider - not affiliated with or authorized by Icynene - which means we evaluate your specific failure without a manufacturer’s agenda driving the recommendation. Our technicians are background-checked and uniformed, and your call is answered by a live person, 24/7, not a voicemail loop with a callback window measured in business days.

We’ve sealed and insulated 9,000+ homes since 2016, and we bring that envelope discipline to every Icynene removal: air sealing first, insulation second, numbers on paper to prove it. We also service Reflectix and other brands, so if your Cedar Park home has a hybrid assembly or you’re considering a material switch, we can compare real performance data rather than steering you toward a single product line. The 365-Day Done Right Promise applies to every completed job, backed by a written scope and warranty delivered before anyone lifts a tool.

FAQs