Owens Corning Home Energy Audit in Cedar Park: What to Know First
We provide independent Owens Corning home energy audit in Cedar Park, typically scheduling within 48 hours and completing most audits same-day. Our written price before any work starts runs between $280 and $620 depending on the audit scope, and we publish before-and-after blower-door numbers so you can verify the result yourself. This page is for homeowners running Owens Corning insulation systems - Pink Next Gen Fiberglas, ProCat, or AttiCat blown-in lines - who suspect their envelope is leaking conditioned air faster than it should. Call (737) 245-6428 for a free estimate or to book an audit slot.
How Owens Corning Products Fail - and How We Fix Them
- AttiCat settled density in older Cedar Park installs. The loose-fill system blown before 2019 in neighborhoods like Buttercup Creek often settled below labeled R-value after our hot summers cycled the attic air above 130°F repeatedly. We measure settled depth with a ruled probe, calculate actual R-value against the bag stamp, and recommend either top-off with fresh ProCat or full removal if the original material compressed below 70 percent of spec.
- ProCat moisture gain in vented attics with bathroom exhaust leaks. Owens Corning’s blown fiberglass resists mold better than cellulose, but saturated ProCat still loses loft. We find this where flex duct pulls off bath fans in Ranch at Deer Creek and Cypress Mill homes. Our fix: seal the exhaust penetration with fire-rated foam, replace the compromised ProCat, and run a blower-door verification to confirm the leak is gone.
- Pink Next Gen batts with compressed top plates in 2015-2020 builds. Builders in Cedar Park’s fast-growth years often stuffed batts tight against top plates, crushing the fiberglass and creating thermal bypasses. We remove the compressed section, air-seal the plate with acoustic sealant, and reinstall with proper friction fit so the batt recovers its labeled thickness.
- AttiCat around can lights pre-ICAT rating. Older Owens Corning installs in Cedar Park frequently buried non-ICAT recessed housings, a fire hazard and air leak. We pull back material, install fire-rated covers, seal the penetration, then redeploy ProCat or AttiCat at proper clearance. The blower-door test proves the fix.
- Reflectix radiant barrier tape failure in hybrid systems. When Owens Corning fiberglass was paired with Reflectix radiant barrier in Cedar Park attics, the foil tape often delaminated after three to four summers of 140°F peak temperatures. We remove failed tape, clean the substrate, and reseal with high-temp acrylic adhesive rated for Texas attic conditions.
Our Owens Corning Home Energy Audit Process
- 1
Call intake with scope lock. A live person answers 24/7. We confirm your Owens Corning product line, home age, and symptoms, then schedule the audit with a written price range texted before we arrive.
- 2
Pre-install blower-door test. We depressurize the house to 50 Pascals and record CFM50 - the single number showing how much conditioned air your envelope leaks. Wes Okafor started doing these at Olive-Harvey College before most Texas crews had heard the term, and we still treat this as non-negotiable baseline data.
- 3
Thermal imaging and insulation inspection. Our FLIR camera maps temperature differentials across Owens Corning batts or blown-in, revealing settled areas, moisture pockets, or compression gaps the eye misses.
- 4
Duct leakage test if indicated. We pressurize the duct system and measure leakage to outside, since Cedar Park’s flex duct runs often pull attic air through failed connections.
- 5
Written scope with parts call. We specify OEM Owens Corning replacement material or compatible aftermarket (Johns Manville, Knauf) where appropriate, with warranty implications noted. No work starts until you sign the written scope and price.
- 6
Air sealing first, then insulation, then post-test. We seal top plates, can lights, and penetrations before adding any material. The final blower-door reading goes on your invoice alongside the photo record. Seal the leaks first. Then insulate. The order matters more than the product.
What Owens Corning Home Energy Audit Costs in Cedar Park
| Audit Scope | Typical Range | What Moves It |
|---|---|---|
| Basic blower-door + thermal imaging | $280 - $380 | Home size under 2,500 sq ft, single HVAC zone |
| Full audit with duct leakage test | $420 - $520 | Two-story homes in Buttercup Creek, dual-zone systems |
| Comprehensive with insulation removal scope | $520 - $620 | Attic access constraints, rodent damage, multiple material types |
Price drivers in Cedar Park: attic accessibility (some Ranch at Deer Creek homes have scuttle holes too small for a technician with gear), number of penetrations to seal, and whether we’re testing a single system or a zoned setup with multiple air handlers. Every estimate is free, written, and valid for 30 days. Call (737) 245-6428 for your exact number.
Why Cedar Park Homeowners Call Topside Attic Insulation Cedar Park for Owens Corning Work
We’ve sealed and insulated over 9,000 homes since 2016, every one with a written price before work started and a documented record when the crew left. Our 365-Day Done Right Promise applies to all completed work - if the blower-door number doesn’t hold, we return. Technicians are background-checked, uniformed, and trained on Owens Corning’s specific density and coverage requirements, not generic “blown-in” practice. We also service Reflectix radiant barrier systems, so hybrid installs get coherent treatment rather than finger-pointing between trades. Calls are answered by a live person, 24/7, and we provide free second opinions on any written estimate you’ve already received.
FAQs
No. Owens Corning’s product warranty covers material defects regardless of who installs or services it, provided the original installation met their coverage and density specifications. We document our work with photos and blower-door readings so you have evidence if a claim ever arises. For audit-related adjustments, call (737) 245-6428 and we’ll review your warranty status before scheduling.
Most audits schedule within 48 hours and finish same-day. Emergency scheduling - for instance, when a homeowner detects a sudden spike in cooling load after a roof leak - sometimes happens next-day depending on crew availability in the Buttercup Creek and Cypress Mill areas. Call (737) 245-6428 to check current openings; estimates are free.
Repair makes sense when settled ProCat or AttiCat still tests above 70 percent of labeled R-value and shows no moisture damage. Full removal and replacement is the better call when we find compressed batts, rodent contamination, or multiple failed penetrations that compromise the entire thermal boundary. We give you both options in writing with price and performance projections before you decide.
We source from Owens Corning, Johns Manville, Knauf, and other named manufacturers depending on availability and your specific need. We do not claim exclusive or preferred status with any brand. When we substitute compatible material, we note it on the written scope and explain any warranty or performance difference. No proprietary lock-in, ever.
You receive a Documented Photo Record of all accessible areas, the written scope with actual pricing, and on applicable jobs the before-and-after blower-door readings in CFM50 and ACH50 - the pressure-to-airflow figures that tell you exactly how leaky your envelope was and what we changed. This is standard on every job, not available on request.
Written by Wes Okafor, Owner, Topside Attic Insulation Cedar Park at Topside Attic Insulation Cedar Park, serving Cedar Park and nearby areas.